What materials can SheetCNC cut? SheetCNC is designed to cut hardwood and softwood – including solid timbers, full-size birch ply, red-and-white ply, shuttering ply, and MDF. These materials are generally available up to 25mm thickness, and SheetCNC can cut to this depth (in several passes) using 6mm cutters. The realistic maximum thickness of these hard materials that could be machined – using long 1/4″ cutters – would be about 40-50mm but that’s taking it to the limit. If you are regularly wanting to cut hard materials which are thicker than 30mm, SheetCNC probably isn’t for you.
SheetCNC can also cut other solid materials including rigid PVC, polycarbonate, HIPS, HDPE and expanded PVC boards. The upper thickness limit with these materials is around 10mm, simply because SheetCNC has no option for coolant flow (onto the workpiece). This means that plastics will tend to overheat and melt, and then bind to the cutter. So only slow, shallow cuts are feasible in plastic. This means that workpiece throughput, when cutting plastics, is quite limited. If plastic cutting is the majority of your work, you should seek a machine which offers workpiece coolant flow because you’ll be able to work much faster.
We’ve also cut rigid foam sheets (‘Jablite’ (TM) and ‘Celotex’ (TM) ) up to a thickness of 100mm, using long cutters. In general, cutters available at this length are much larger than 6mm dia. However, the material being cut is much less dense than timber so deflections are not a significant issue and the large cutters work fine in this limited application.
At the other end of the size scale we’ve used SheetCNC to etch and drill tiny double-sided electronic printed circuit boards. Again, that’s not something that should be your prime reason for buying a SheetCNC. But by taking extra care to set up the workpiece perfectly flat – or by using mesh-leveling software – you can realistically cut the occasional through-hole PCB. SheetCNC isn’t going to get you down to the smaller scales needed for surface-mount, though.
Can I use larger cutters on timber? What about drilling large holes? It depends…
- For surfacing, timber a 1″ CEL cutter is ideal.
- Drills up to about 8mm are fine in most timbers. But even the 2.2kW water-cooled spindle won’t go slow enough to use larger drills than that without a pilot hole. At low speeds, it just doesn’t have the necessary torque. So, for making precise large holes, mill out a slightly undersize hole using a 6mm cutter then ream it with a twist-drill.
- For all other operations in timber, 6mm (1/4″) CEL is the realistic maximum cutter size.
Can SheetCNC machine metals? No. SheetCNC is not designed for metalworking. It is not rigid enough and there is no way to apply coolant to the workpiece.
Not even aluminium, which is very soft? Still no, sorry, because although aluminium is soft, it also binds to the cutter and clogs it completely unless there is a constant flow of coolant. SheetCNC isn’t suitable for using with coolant.
Can SheetCNC do 3D work? Yes, up to the modest limits of the Z clearance (which is just 100mm after allowing for the spoilboard and some margin). But if intricate 3D work is your main reason for buying a CNC machine, better to look for one that can achieve very high accelerations because the tool must frequently and sharply change direction during 3D carving. Whereas in 2.5D machining, more modest accelerations are acceptable.
How much space does SheetCNC occupy? The full-sheet machine is 1.65m wide by 2.9m long. The half-sheet machine is 1.65m x 1.65m. In addition you’ll need space to move around the machine, plus a nearby shelf or small worktop area for the controller. Several of our customers have positioned their SheetCNC tight into the corner of a room, so that they have access to only two of its sides. This is not ideal but it is a workable option if space is limited.
Suppose I need a vacuum-bed – can I do that? Our experience with vac-beds is that they are wonderful… when they work. We get very good results from small vac-beds which we use for holding printed circuit boards and sign-making laminates while we etch them. A vac-bed has the advantage that it holds even extremely thin and flexible materials perfectly flat. We have also tried using an 8′ x 4′ vac-bed but then even a massive 3kW side-channel vac-pump struggles to maintain sufficient vacuum. Consequently we don’t recommend trying to set up a large vac-bed: it just won’t work.
How are the axes driven? The X and Y axes are driven by high-torque stepper motors acting on a high quality miniature chain drive. The Z axis is leadscrew driven.
Chain drive? Really? How accurate can that be? Do take a look at the videos at the bottom of this page. Our chain mechanism has been designed to offer an inherent chordal position error of less than 0.15mm – quite negligible when compared to the other tolerances of SheetCNC. Unlike a leadscrew, chain suffers virtually no backlash error. And, unlike toothed belt, chain is extremely robust in a workshop environment. Chains don’t clog, won’t shred, aren’t prone to skipping, and won’t need constant cleaning to keep them free of cuttings. In short, chain is just about the perfect drive mechanism for a budget light-duty CNC router.
Chain must have some disadvantages – otherwise everyone would be using it instead of expensive leadscrews and racks? Chains – like belts – have some degree of elasticity. This means that the harder the machine is worked (for example by using large cutters, high feedrates, large depths-of-cut) then the greater the dimensional errors of the finished product. This is why we recommend using small diameter cutters and making precision cuts in modest depth steps, so as not to push the machine too hard.
Could I fit a modified manual router, instead of a water cooled spindle? For sure, if you modify the tool holder appropriately. But please let us try to dissuade you because there are many advantages to water-cooled spindles. The spindle we recommend is software-controlled, so its RPMs are set in the CNC program rather than by dialing manually as on a typical router. Water-cooled motors can be run at much slower speeds which is especially important when drilling. Water-cooled spindles won’t clog with chips and overheat. Air-cooled routers emit a constant blast of high-speed airflow which blows cutting dust into the air in the workshop, increasing the respiratory hazard. And air-cooled routers are noisy, which can be a problem in a residential area. The modest extra cost of a water-cooled spindle is well worth it.
Chain Chordal Error
This is something we’re constantly asked about. Maybe it’s the fancy name that makes it stick in people’s minds? Anyway, here’s a video to show why it’s hardly an issue:
The video was filmed on a Mk3 SheetCNC which is about a year old and has seen some heavy use.
The machine has all-original mechanical parts, identical to those supplied in UK-DIYcnc’s kit.
Backlash
Another popular question. Again, it’s really not an issue, in comparison to the other tolerances inherent in the machine. Here’s the test: